NOTE: This is a 3.3V Shield, Only Use it with a 3.3V Arduino Variant!Tutorial Can Be Found HERE.Bluetooth
Shield, a serial port Bluetooth module (Mas..
Ever wanted to connect your Arduino or electronics project to a phone or computer over Bluetooth then this is the perfect module for you. The HC-06 bl..
The mega menus use the page builder interface and this means you can add any layout module in your menus to build the desired layout in any rows and columns combination.
This compact and affordable USP programmer is perfect for reading and writing 24 series EEPROM devices and 25 series SPI FLASH devices. It has a 16 pin ZIF socket for easy insertion and removal of chips to make sure the legs are not damaged.Supported Chips: (NOTE: ESMT CHIPS READ SUPPORT ONLY NO WRI..
This is a general purpose USB to TTL module. It features a VCC jumper so you can use it on both your 3.3 and 5V devices.Features:Switchable 5V/3.3V powerStatus LEDUSB to TTLVCC, GND, TX, RX Pins..
<p><br>Usb_x000D_
ISP programmer for programming Altera's range of FPGA and CPLD device._x000D_
This programmer is compatible with Altera's Quartus development tools_x000D_
(Use USB blaster in programmer hardware settings).<br><br>Kit includes<br>1 X device<br>..
his
general USB to TTL module has many uses. This module also includes a
DTR pin out connection so you can easily program your Arduino Pro
Mini's with out the need to manually reset them.Features:Chipset: CP2102.USB Version : 2.0USB Connection: A MaleTTL 6 Pin Header:DTRRXDTXDVCCCSTGND500 mA Self..
This
CP2102 USB to TTL converter features both a 3.3V pin and 5V pin so you
can easily communicate with device with different voltage levels.Pin Connections:3.3VRST5VTXRXGND..
This
is a compact and convenient module offering both a programming
interface for PICkit 2 and 3 as well as a minimal development
environment for your PIC based projects.Features:LED can be connected to any I/OCrystal Socket can be connected to any pin A Button (do reset key).Complete Pin Br..
This
is the module you want if you are programming a stand alone Arduino or
Pro Mini, or most variants when you need an external module. This
module includes break outs for the DTR line for auto reset so there is
no need to try to manual reset the Arduino when loading your program.Features:Genui..
Support the most popular PIC chipsNo external power supply neededPICSTARTPLUS much faster rate than programmingAutomatic programming verificationComprehensive information prompts, allowing users to understand the working state.With a 40pin ZIF programming of the seat can directly program ..
This
module allows you to connect RS232 devices which normally operate upto
13V to TTL devices which normally operate at 3.3 or 5V so they can
communicate.Specifications:IC:MAX3232CSEModule Voltage: 3-5V DCMax Baud Rate: 120kbpsSize (W x L): 9.4mm*15.9mm..
The
MAX485 is low-power transceivers for RS-485 communication. The IC
contains one driver and one receiver. The driver slew rates of the
MAX485 is not limited, allowing them to transmit up to 2.5Mbps. These
transceivers draw between 120μA and 500μA of supply current when
unloaded or fully loade..
NOTE: This is not made by Microchip it is a similar device that is nearly identical and functionally equivalentThis
PICkit 3 compatible device is an in-Circuit Debugger/Programmer it uses
in-circuit debugging logic incorporated into each chip with Flash
memory to provide a low-cost hardware debug..
NOTE: This is not made by KEIL/ARM, however it is fully compatible with all the ULINK 2 Features and FunctionalityThis
ULINK2 compatible Debug Adapter connects your PC's USB port to your
target system (via JTAG, SWD, or OCDS) and allows you to program and
debug embedded programs on target h..