NOTE: This is a 3.3V Shield, Only Use it with a 3.3V Arduino Variant!Tutorial Can Be Found HERE.Bluetooth
Shield, a serial port Bluetooth module (Mas..
Ever wanted to connect your Arduino or electronics project to a phone or computer over Bluetooth then this is the perfect module for you. The HC-06 bl..
The mega menus use the page builder interface and this means you can add any layout module in your menus to build the desired layout in any rows and columns combination.
This
is a mini DC-DC buck converter step-down power module,capable of
driving a load up to 3A with high much higher efficiency then a linear
regulator. Input voltage: 4.5-28VOutput Voltage: 0.8-20V (adjustable)Output current: rated current 3A(MAX).Switching Frequency: 1MHzOutput Ripple:less than ..
This
high efficiency KIS3R33S buck module is perfect for stepping down a
7-24V DC input and outputs it to a 5V standard female DC socket.SpecificationsType: Non-isolated BuckRectification: Non-synchronous rectificationInput voltage: DC 7- 24VOutput voltage: DC 5VOutput current: 3A (max)Conversion ..
This
DC-DC step down power regulator is perfect for helping control voltage
levels in your project. It is capable of converting 4-40V DC sources to
1.25-37V DC output(input must be at least 2V above output). Output
voltage is easily controllable through the on board potentiometer. It
features a..
This
LM2596 module is capable of taking a 3.2-40V to 1.25-37V DC(output
lower than the input). Features an on board potentiometer for easy
voltage control. This module is capable of driving a load of up to 3A
but a heat sink must be used if the output is greater then 2.5A or 10W...
This
DC-DC step down power regulator is perfect for helping control voltage
levels in your project. It is capable of converting 4-40V DC sources to
1.25-37V DC output(input must be at least 2V above output). Output
voltage is easily controllable through the on board potentiometer. It
features a..
<p><br>This_x000D_
LM2596 module is capable of taking a 4.5-60V to 3-35VDC(output lower_x000D_
than the input, minimum difference 1.5V). Features an on board_x000D_
potentiometer for easy voltage control. This module is capable of_x000D_
driving a load of up to 3A but a heat sink mus..
This module is a high efficiency adjustable DC to DC step down buck regulator based on the MP2307 IC. It features a wide input range of 4.75-24V with rated 2.5A continuous output current. This module also features a convenient ON/OFF switch.Specifications:
Input voltage: 4.75-24V
Output vol..
The LM 7805 is a voltage regulator that has been around for a long time, the problem is that it is a linear power regulator. This means that stepping down a voltage is done by turning the excess into heat leading to high power loss and excessive heat build up.
This tiny switching DC-DC buck voltage..
This
high efficiency KIS3R33S buck module is perfect for stepping down a
7-24V DC input and outputs it to a 5V standard female DC socket.SpecificationsType: Non-isolated BuckRectification: Non-synchronous rectificationInput voltage: DC 7- 24VOutput voltage: DC 5VOutput current: 3A (max)Conversion ..
This high efficiency (97.5% peak) DC to DC buck converter is capable of taking a 6-24V DC power source and outputting it to a female USB A port perfect for powering a USB device. This converter is capable of supplying up to 2.1A continuous and 3A peak.
This module also reverse polarity protection,..
This is a mini DC-DC buck converter step-down power module, capable of driving a load up to 3A Peak (1.8A continuous) with high a higher efficiency then a linear regulator.
Specifications:
Model: Mini-360
Regulator IC: MP2307
Regulator Type: Step Down, Buck
Input Voltage: 4.75-23 VDC
Output ..
This DC-to-DC step down buck converter is based on the XL4015 IC. This module can be run in eihter Constant Voltage (CV) or Constant Current mode. It featuures a built in display capable of measuring and siplaying This module has a built in meter capable of measuring and displaying input/output volt..