NOTE: This is a 3.3V Shield, Only Use it with a 3.3V Arduino Variant!Tutorial Can Be Found HERE.Bluetooth
Shield, a serial port Bluetooth module (Mas..
Ever wanted to connect your Arduino or electronics project to a phone or computer over Bluetooth then this is the perfect module for you. The HC-06 bl..
The mega menus use the page builder interface and this means you can add any layout module in your menus to build the desired layout in any rows and columns combination.
While our standard MG90S servo is great in many applications sometimes the plastic gears may not be enough. This servo has metal gears where a more rugged solution is needed.Specification:Operating Speed (no load): 0.11sec/60 degreesStall torque: 2.2kg/cmOperating Voltage: 4.8-6.0VTemperature Range:..
This stepper motor and motor driver is the perfect way for quickly hooking up a small stepper motor you your project. All you need is 4 control wires, power and ground and you can be up and running in a few minutes. The 28BYJ-48 has 64 steps given you lots of control in rotation. The preassembled UN..
This small module is capable of driving two DC motors from 2.5-12V at currents up to 800mA. Specifications:Controller IC : HG7881Input Voltage : 2.5-12VSize : 30 x 24 x 14 cm Weight : 7gPin Description:B-IA: Motor B Input A (IA)B-IB: Motor B Input B (IB)GND: GroundVCC: Operating Voltage (2.5-12V DC)..
This
module allows you to easily control either 2 DC motors or one 4-wire
2-phase stepper motor from your microcontroller or Arduino project.Features:2.5-12V Supply VoltageContinuous 800 mA outputCan drive two DC motor or one 4-wire-2-phase stepper motorsNOTE:
Please be careful when supplying VCC..
The L298N is a Dual H-Bridge motor controller can control up to 2 DC motors or 1 stepper motor.Features:: Chip: L298N
Logic Voltage: 5V
Logic Current 0mA-36mA
Operating Mode: H-bridge, Dual
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions..
This is a metal geared, 360 degree, 55g servo. Perfect for steering your RC project or adding movement to your Arduino project.Features:Color: BlackSize: 40.5 x 43.5 x 20 mmCable length: 280 mmMaterial: ABS plasticAngle: 360 degreeTorque force: 13kg..
<p>This servo tester easily allows you to test your servos without having to hook them up to a controller. This servo is capableof testing up to 3 servos and has 3 conveinient modes:<br /><br /></p><ul><li>Manual mode, turning the potentiometer changes the servo p..
The SG90 servo is a small and affordable servo perfect for adding
movement to your project. The servo comes with several different
adapters making it easy to hook up to most devices.Features:Model: SG90Weight: 9gDimension: 23*12.2*29mmStall torque 1.8kg/cm(4.8V)Operating speed: 0.1sec/60degree(4.8..
This
SG90 servo mount/holder makes it easier to mount your SG90 servo to
something solid. The bottom mounting slot is slotted to allow for more
flexible mounting locations and choices...
The
preassembled UNL2003 driver board features a built in UNL2003 stepper
motor driver, indicator LEDs for which coil is engaged, and a header
for easily connecting a stepper motor..
Many
motor drivers are limited to driving fairly small loads, this motor
driver based on the VNH2SP30 allows you to drive much larger loads.
With a peak output of 30A and a continuous rating of up to 14A (with
additional cooling) you can drive some fairly large motors. Without any
additional co..
This adjustable DC motor speed controller is capable of controlling motors from 6-28V DC. It includes a built-in potentiometer with knob for easy adjustment of the PWM single with an adjustable duty cycle of 5-100%.
Specification:
Operating Voltage: 6-28V DC
Maximum Current 3A
Duty Cycle: 5-10..