NOTE: This is a 3.3V Shield, Only Use it with a 3.3V Arduino Variant!Tutorial Can Be Found HERE.Bluetooth
Shield, a serial port Bluetooth module (Mas..
Ever wanted to connect your Arduino or electronics project to a phone or computer over Bluetooth then this is the perfect module for you. The HC-06 bl..
The mega menus use the page builder interface and this means you can add any layout module in your menus to build the desired layout in any rows and columns combination.
<p>If_x000D_
you have ever wanted to add short range line-of-site remote control to_x000D_
your electronic or Arduino project, if so this is the perfect kit for_x000D_
you. This kit includes a miniature IR remote, a HX13838 IR receiver (NEC_x000D_
protocol), its corresponding base module f..
Microcontroller
pins are limited to outputting small voltages and currents. If you wish
to drive a larger load you need some sort of adapter. This convenient
module allows you to easily connect devices upto 24V and currents
of 1A(Higher if you apply a heat sink). This module features conve..
This
ISD1820 allows you to record up to 10 seconds of audio at 5.3 KHz
sampling rate. It features both buttons on board to control it and also
a pin header breakout so it can be controlled by your microcontroller.
Has a built in 8 ohm speaker driver capable of driving a small speaker.Features:Pu..
This
module is based off of the LM358 op amp. This module is easy to connect
with a standard 2.54 mm pitch pinheader and onboard potentiometer for
gain adjustment.Specifications:LM358 chips100 Times GainGain adjustable Bia Onboard PotentiometerOnboard Power LED IndicatorWorking Voltage: 5-12V DC..
This is a small low cost amplifier used to run a small speaker for your electronics projectFeatures:LM386 chip200 gain circuit designSpeaker Wire Screw Terminals10K Potentiometer for Volume AdjustmentPower Indicator LED5-12VDC Operating VoltageBoard size: 40.7 (mm) x13.7 (mm)..
Outputting
an analog single is not always possible with all microcontrollers
especially with the Raspberry Pi. The MCP4725 board provides this DAC
capability in a small and affordable package.The MCP4725 is a
low-power, high accuracy, single
channel, 12-bit buffered voltage output Digital-to-An..
The
MFRC522 is a highly integrated reader/writer IC for contact less
communication at 13.56 MHz. The MFRC522 reader supports ISO/IEC 14443
A/MIFARE mode. The MFRC522’s internal transmitter is able to drive a
reader/writer antenna designed to communicate with ISO/IEC 14443
A/MIFARE cards and tra..
This
MicroSD card adapter module easily allows you to connect your Arduino
or other microcntroller to a Micro SD card over an SPI interface. This
module is compatible with the Arduino SD card library. Features:Supports both Micro SD Card, Micro SDHC Logic Level Conversion Supports Both 5V a..
The
PCA9685 is an I²C-bus controlled 16-channel is 12-bit resolution (4096
steps) fixed frequency individual PWM controller that operates at a
programmable frequency from a typical of 24 Hz to 1526 Hz with a duty
cycle that is adjustable from 0 % to 100 %.Each output can be
off or on (no PWM co..
The PCF8591 is a single-chip, single‑supply low‑power 8‑bit CMOS data acquisition device with four analog inputs, one analog output and a serial I²C‑bus interface. The functions of the device include analog input multiplexing, on-chip track and hold function, 8-bit analog‑to‑digital conversion and a..
This
is a replacement wheel compatible with our robot chassis kits. It is
perfect if you have lost or damaged yours or you need one for any of
your other projects.Wheel Specifications:Axle Hole: 5.3mm x 3.66mmDiameter: 66mmWidth: 26mm..