NOTE: This is a 3.3V Shield, Only Use it with a 3.3V Arduino Variant!Tutorial Can Be Found HERE.Bluetooth
Shield, a serial port Bluetooth module (Mas..
Ever wanted to connect your Arduino or electronics project to a phone or computer over Bluetooth then this is the perfect module for you. The HC-06 bl..
The mega menus use the page builder interface and this means you can add any layout module in your menus to build the desired layout in any rows and columns combination.
This 12V delay module is perfect when you want to delay powering a device. The delay is adjustable from 0-10 seconds. These are commonly used in automotive application when you want to delay powering a device until after the car starts. These are also great to use when one event needs a delay trigge..
Connecting and wiring up your devices can often be difficult when working with your electronics projects, especially with your NodeMCU with its limit number of GND and 3V pins. This breakout board features a socket for your NodeMCU, extra connections for all the pins of the NodeMCU and extra 3, 5V ..
This NodeMCU module is a development board based on the ESP8266 wifi
circuit.It is compatible with both the Arduino IDE and LUA language. It feature both a built in ESP-12 WiFi chip and a CH340G USB
controller so you can easily communicate and program the module through
your PC without any additi..
This NodeMCU module is a development board based on the ESP8266 wifi
circuit.It is compatible with both the Arduino IDE and LUA language. It feature both a built in ESP-12 WiFi chip and a CP2102 USB controller so you can easily communicate and program the module through
your PC without any additio..
The
NRF24L01 is a versatile and affordable transceiver, however it poses
some problems operating with a 5V microcontroller as it runs at 3.3V
and has strict power reliability requirements. This module helps to
easily solve this problem with its built in 3.3V regulator and bypass
capacitor suppl..
The PAM8610 is a 10+10W dual channel stereo Class-D audio amplifier with DC Volume Control which offers low THD+N (0.1%), low EMI, and good PSRR thus high-quality sound reproduction. The PAM8610 runs off of a 7V to 15V supply at much higher efficiency than competitors’ ICs.
Features
10W @ 10%THD..
This
module allows you to connect up to 8 digital I/O ports to a single
device on the I2C Bus, this means you can gain up to 6 digital I/O
ports (or 8 if the 12C bus is already being used) so you can connect
more devices to your project. This module also features 3-dip switches
to change the I2..
When your heart beats the volume of blood in your finger changes. By incorporating an optical heart rate sensor with amplification and noise cancellation circuitry this simple module easily allows you to detect a pulse or heartbeat. The pulse sensor incorporates pre-soldered wires with built in male..
This vibration motor module incorporates a vibration motor that you would usually find in a device like a phone with all the necessary circuitry to hook up to your electronics project. With a standard 0.1” pin header this module is easy to connect. This module operates at 5V and the “intensity” of t..
This module easily allows you to detect rain or other moisture and then activate a relay. Essentially the sensor plate acts as a large resistor, as rain falls on the plate it bridges the gaps and the resistance decreases. The output is controlled by the adjustable on board comparator, you can adjust..
The
RCWL-0516 is a Doppler radar microwave motion sensor module it uses a
microwave Doppler radar to detect moving objects unlike many other
motion sensors that used IR changes. When the module
detects movement the output is set high for several seconds. The
maximum range for motion detec..
The
RDA5807M series is the newest generation single-chip broadcast FM
stereo radio tuner with fully integrated synthesizer, IF selectivity,
RDS/RBDS and MPX decoder. The RDA5807M has a powerful low-IF
digital audio processor for optimum sound quality. The RDA5807M series
support frequency..